SkyWand: Setup & getting started, every question, answered
36 answers below, written from the manufacturer's manuals and our own bench experience. Prefer to tap through them? The same answers power the live chat in the corner. Ready to buy? See the SkyWand or request a quote.
What's the first step after unboxing?
Fully charge a battery, the manual requires a full charge before first use. Expect about 4 hours on the included charger.
How do I charge the batteries?
Seat the pack so its anode meets the charger's anode and its cathode meets the cathode, then plug the charger into main power. The light shows red while charging and green when full.
How do I know charging is complete?
The charger's indicator light turns from red to green when the battery is fully charged. A full charge takes approximately 4 hours.
How does the battery go into the lamp?
Insert one fully charged battery into the lamp handle with the anode forward and the cathode at the tail, then close the handle.
How do I turn the UV light on and off?
Press the switch button on the lamp to turn the UV light on or off. Put the goggles on first.
How do I swap battery packs?
Open the handle, remove the spent pack, and insert a charged one with the anode forward and the cathode at the tail. It takes seconds, so keep the second pack topped up.
Should I keep the spare battery charged?
Yes, charge one pack while the other is in the lamp. That rotation is what gives the SkyWand its all-day runtime.
How do I clean the optical lens?
Turn the UV light off first, then clean the lens with lens tissue or a non-dust cloth and alcohol.
How often does the lens need cleaning?
In use, the lens picks up environmental dust and volatiles from UV glue, which robs output. Clean it whenever it looks contaminated to keep full UV power on your parts.
How do I verify UV output over time?
Measure the intensity periodically with a UV-A radiometer. If it's no longer powerful enough for your glue curing, contact us about a new UV light source replacement.
How do I set the right exposure time?
Your adhesive datasheet lists the wavelength and dose it needs; time the exposure to reach that dose. The SkyWand's single switch leaves timing under your control.
If you'd like help translating a datasheet into a procedure, ask us on a quote request.
How should I store the SkyWand?
Keep the kit in its plastic carry case, and keep the optical lens away from liquid, dust, and other pollutants.
Does the lamp show battery level?
The manual doesn't describe a charge gauge on the lamp, the status light lives on the charger. Output holds constant until the pack is empty, so keep the spare charged and ready.
Which way do packs sit in the charger?
Match polarity: battery anode to the charger anode, cathode to cathode. Then plug the charger into main power.
Can I charge two packs at once?
Yes, the manual's charging illustrations show two packs seated in the included charger together. The indicator shows red while charging and green at full charge.
Can I use one pack while one charges?
Yes, that's the intended workflow. Run one pack in the lamp while the second sits on the charger, then swap.
Which way does the battery face in the lamp?
Anode forward, toward the lamp head, with the cathode at the tail. The manual's diagram shows the orientation.
Any warm-up routine before curing?
None, press the switch and you're at full output instantly. There's no stabilization wait and no cool-down cycle described.
Output seems weaker than before - what now?
First clean the optical lens (UV off, lens tissue or non-dust cloth with alcohol), dust and UV glue volatiles are the usual culprits. Then measure with a UV-A radiometer; if it's still too weak for your glue, contact us about a UV light source replacement.
How do I protect the lens day to day?
Keep it away from liquid, dust, and other pollutants, and clean it with lens tissue and alcohol when needed. A clean lens is what keeps full UV power on the part.
Do I need to buy anything else to start?
No, the kit includes the lamp, charger, two batteries, goggles, and case. The one add-on worth considering is a UV-A radiometer for periodic intensity checks, which isn't included.
Is any assembly required?
No assembly, just charge a pack, insert it anode-forward into the handle, and press the switch.
Should I read the manual before starting?
Yes, Uvitron asks that you read it carefully before use and keep it handy for reference. It's a short read covering charging, operation, safety, and maintenance.
Where do I get help if I'm stuck?
Start with our tech support page, or email sales@uvspotshop.com Monday-Friday during US business hours. We'll walk you through setup.
How soon can a new unit make its first cure?
About 4 hours after unboxing, that's the required full first charge. Then insert the pack, put on the goggles, and cure.
Does the lamp itself plug into power?
No, the lamp is cordless and runs only on its battery. Only the charger connects to main power.
Can packs stay on the charger overnight?
We don't recommend it as a habit, Uvitron cautions that overcharging shortens battery life. Once the indicator turns green the pack is full, so take it off when convenient.
Will I get a warning before the pack dies?
No fade warning, that's by design. Output stays at full strength until the battery is empty, so keep the spare charged and swap when the lamp stops.
What supplies do I need for lens cleaning?
Lens tissue or a non-dust cloth, plus alcohol. Turn the UV light off before you start.
Can I clean the lens while it's running?
No, the manual says to turn off the UV light before cleaning. It only takes a moment.
How do I maximize battery lifespan?
Avoid repeated deep discharges and don't overcharge; swap packs before they're run completely flat when practical. Cared for this way, packs are rated for 300-500 cycles or more.
Is a radiometer included in the kit?
No, the packing list is lamp, charger, two batteries, goggles, and case. The manual recommends periodic checks with a UV-A radiometer, so plan to source one if your process requires documented intensity.
How often should intensity be measured?
The manual says to measure periodically with a UV-A radiometer, without fixing an interval. Set a cadence that fits your quality process, many shops tie it to their regular QA checks.
What if the LED source wears out?
If measured intensity is no longer enough for your glue curing, contact us, the manual's remedy is a new UV light source replacement, arranged through us.
What's the best way to move it between sites?
In the included plastic carry case, it holds the lamp, charger, packs, and goggles, so the whole curing station travels as one box.
Do battery swaps need tools?
No tools, open the handle by hand, drop in the charged pack anode-forward, and close it back up.
